How Much Do DCS Grill Parts Cost? [2026 Prices]

DCS started as Dynamic Cooking Systems, a California company that built some of the first serious stainless built-in grills. Fisher and Paykel has owned the brand for years now, and DCS grills are still common in higher-end outdoor kitchens. Many of the DCS grills we work on are 10 to 20 years old and still worth fixing. The frame and firebox hold up. What wears out is ignition, burners, radiant trays and, slowly, grates.

DCS grill parts prices

Prices checked October 2026 from authorized dealers, the Pro Grill store and Amazon. Always match the part to your model and serial number.

What DCS grill parts cost in 2026

Most DCS parts run about $10 to $350. Small aftermarket electrodes are at the bottom. Factory burners, grate sections and the sear burner are at the top. That's well above Weber replacement part prices and in the same range as other premium built-ins like Viking and Lynx.

The big thing to know about DCS is how wide the gap is between factory and aftermarket. A factory DCS burner runs about $245 to $300. A good aftermarket burner for the same grill runs about $70 to $140. On grates the gap is even bigger: about $270 to $300 per factory section versus about $98 aftermarket.

Part-by-part breakdown

Burners

DCS used several burner designs over the years: straight tube burners, U burners, and cast burners on some 36 and 48 inch models. Factory replacements we saw ran about $245 to $300 each, and the BGA tube burner for some older 26 inch grills was over $450. Aftermarket stainless and cast iron versions run about $70 to $140. The sear burner assembly on infrared models is about $345.

Burners that look alike can differ by half an inch or by where the mounting tab sits. Pull one and measure before ordering. Our burner price guide compares DCS to other brands.

Valves

Factory DCS valves run about $85 to $130. Some older E-series grills have an aftermarket brass valve near $25, but for most DCS models the factory valve is the only real choice. Valves come with or without a microswitch for the reignition system, and propane and natural gas versions differ. Buy the factory valve for your exact model and fuel type and have it leak tested after install. More in our gas valve cost guide.

Radiant rod trays

DCS grills use a stainless tray of ceramic rods over each burner instead of a flat heat plate. The rods spread heat and burn off drippings, and they crack or clog with age. A factory tray for 36 and 48 inch grills runs about $125, and the 30 inch tray about $180. Replacement rods are about $14 each or about $66 for a 10-pack, so if the tray is still solid you can just replace broken rods. The 30 inch tray is a different size, so don't order by grill brand alone. See our heat plate and radiant tray guide.

Cooking grates

DCS grates are heavy cast stainless and rarely fail, but they do wear thin and lose their finish after many years. Factory sections run about $270 to $300 each, and a 36 inch grill usually takes about six. That adds up fast. Aftermarket stainless sections for some models run about $98. Older and newer 36 and 48 inch grills use different finger patterns, so compare the old grate before ordering. Our grill grate cost guide covers alternatives.

Ignition

Ignition is the most common DCS repair. Older models used rotary or push-button sparkers. Later BGB and BGC grills used 9 volt battery modules with one outlet per burner. Series 9 and some older E models used hot surface igniters or glow plugs powered through a transformer. Grills with R or AR in the model number have a rotisserie burner with its own electrode and wiring.

Short aftermarket electrodes run about $10 to $30, while long factory electrodes that span the burner cost about $82 to $118. Factory battery modules run about $58 to $172 depending on outlet count, and aftermarket modules about $40 to $55. Hot surface igniters are about $176 to $215, and transformers about $75 to $240. Try a fresh 9 volt battery first. It fixes more DCS ignition calls than any part. See igniter and electrode prices.

OEM vs aftermarket for DCS

DCS has a real aftermarket for burners, grates and ignition, and good aftermarket parts work fine when the dimensions match. For gas valves, regulators and anything that controls gas flow, buy the factory DCS part. A leaking valve is a fire risk, and the savings aren't worth it.

How to find your DCS model and serial number

DCS model numbers look like BGC36-BQAR-N, BGB48-BQR-L or BH1-36R-L. The letters at the end matter. R means rotisserie, and the final N or L tells you natural gas or propane. On most DCS grills the rating label is on the frame behind or under the drip tray, so pull the tray out and look along the inside. Take a photo of the full label, including the serial number. Grills with similar model names from different years can take different parts.

DIY or hire a pro

Batteries, push buttons, short electrodes, rods and grates are reasonable DIY jobs. Burners usually come out with a few screws, though rust can slow that down. Long electrodes, harnesses, transformers and hot surface ignition take more disassembly and testing with a meter. Valve work means opening the gas line and needs a leak test after.

Most service companies in our network are dealers or have dealer accounts, so they can usually pin down the right DCS part and install it on the same visit. You can look up a grill tech by ZIP or browse grill repair companies near you. If the burners and trays are caked in grease, a professional grill cleaning often fixes ignition and uneven heat by itself.

Getting DCS parts through Pro Grill

Pro Grill doesn't list DCS in its online store, but it can source DCS parts. Ask Pro Grill to find the DCS part you need and include the model label and a photo of the old part. Learn more about the brand on our DCS grill page. If your grill needs burners, trays and grates all at once, read our repair or replace guide first. Six factory grate sections alone can cost more than $1,600.

Part prices by type

Frequently asked questions