Mobile service
We come to you in Midway City
A Pro Grill technician drives to your home, sets up beside the grill and does the work there. Nothing gets loaded into a truck, and nobody scrubs a greasy firebox over the driveway.
This matters most for built-ins. A grill set into a block or stone island can't go to a shop, so the work has to happen at the house. We cover Midway City and the neighboring Orange County areas, including Westminster, Garden Grove, Little Saigon, Fountain Valley, Huntington Beach and Santa Ana.
We started in Southern California in 2018 and have serviced over 25,000 grills. We have 2,500+ five-star reviews (Google, Yelp and Facebook), the team has 50+ years of combined grill experience, and we're insured.
Deep cleaning
Deep BBQ grill cleaning
A deep clean is a full teardown, not a quick scrub of the grates. We take the grill apart, clean each piece and put it back together. The job includes:
- Cooking grates, scraped and washed
- Burners, cleaned with every port cleared
- Heat plates or flavorizer bars
- Briquette trays and briquettes
- Firebox, scraped of baked-on grease
- Drip tray and grease management system
- Igniter electrodes, cleaned and tested
- Hood and outside stainless, cleaned and wiped down
- Cleanup of our work area when we finish
Buildup is more than an eyesore. Grease and carbon feed flare-ups. Clogged ports and caked heat plates give you uneven heat, with one side scorching while the other lags. Moisture trapped under grime starts rust, and burners that sit in wet grease rot out early. A clean grill heats more evenly and its parts last longer.

Start with the symptom
BBQ repair at your Midway City home
We repair burners, valves, igniters, grates, briquettes, heat plates, knobs and regulators. These are the problems we get called for most.
Igniter clicks but won't light
Usually a dead battery or module, a dirty or misaligned electrode, or a loose wire. We test the spark, then clean, adjust or replace what's failing.
Flame is low or weak
A regulator stuck in low-flow bypass mode is a common cause, often after a tank valve was opened quickly or a hose leaked. We reset it, or replace it if it won't recover.
Hot spots and uneven heat
Warped or burned-out heat plates, a burner sitting off its valve, or a broken briquette tray are the usual causes. We replace the failed part and set the burners so the flame is even.
Dust in the burner ports
Dust, debris and cooked-on grease block ports and leave patchy flames. We clear every port and replace burners that are too far gone.
Spiders in the venturi tubes
Spiders nest in the burner tubes and choke the gas flow, giving yellow, lazy flames or fire at the knobs. We clear the tubes and check the burner for damage.
Flare-ups and grease fires
Grease built up in the firebox and drip tray is the fuel. We remove it, clean the grease path and replace heat plates that no longer shield the burners.
Heat plates burned through
Flavorizer bars and heat shields thin out over the years and finally burn through. We fit the correct replacements for your model.
Smells like gas
Shut the gas off at the tank or supply and don't light the grill until it's been checked. Loose fittings, cracked hoses and worn valves are the usual sources, and we leak-test the connections and fix the cause.
Repair it right
We diagnose first, then buy parts
The same symptom can come from different problems. A grill that won't heat might have a bad regulator, blocked tubes or a failing valve, and guessing means buying parts you didn't need. So we check the grill first and replace only what's actually wrong.
When you book, send a photo of the model and serial number label. It's usually on the frame, inside a cabinet door or on the back panel. With it we can come ready for your grill. The truck carries parts for most brands, and more are available at store.progrill.com.
Built-ins & outdoor kitchens
Built-in grills and outdoor kitchens in Midway City
When one part fails on a built-in, repair almost always makes more sense than tearing out the island. A new burner, valve or igniter costs far less than rebuilding the cutout and counters around it. We also source parts for most built-in grills.
For bigger projects we design, fabricate and repair outdoor kitchens. We also work on smokers, griddles, pizza ovens, fireplaces and fire pits.

Inspections & maintenance
Inspections and regular maintenance
An inspection is a full check of the gas connections, burners and ignition, finished with a written report. It's useful before the season, when you're buying a house with a grill, or when something feels off but you can't name it.
Most homes should have a deep clean every 6 to 12 months, and more often if you grill several times a week. The Protection Plan membership puts those cleanings on a schedule, so you don't have to remember them.
Wear and tear
What wears grills out in Midway City
Midway City is inland, so heat, dust and spiders do most of the damage. Dust settles in burner ports and under hoods. Spiders move into the venturi tubes. Repeated heat cycles warp heat plates and burn through briquette trays.
A fitted cover helps with the dust. Brushing out the burner tubes before a stretch of heavy grilling helps with the spiders. If the flames turn yellow or the grill takes longer to heat, have it looked at before it gets worse.
When it's time to replace
New grills, measured and installed
Sometimes a repair doesn't make sense, such as a burned-out firebox or a grill that costs more to fix than to replace. In that case we measure the cutout, sell you a grill that fits, install it and haul the old one away.

What to expect
What a visit looks like
- You book online and send a photo of the model and serial number label.
- The technician arrives at the agreed time and looks over the grill with you.
- We explain what we found and what it needs before starting repairs.
- We clean, repair or both, working at the grill.
- We test the grill, clean up our work area and go over what was done.

