Mobile service
We come to you in Brentwood
Pro Grill is a mobile service. A technician drives to your house, sets up next to the grill and does the work there. You don't load a greasy grill into a car, and you don't go weeks without it.
On-site work matters most for built-in grills. A built-in sits in a stone island or a stainless frame and isn't going anywhere, so the cleaning and repair happen where it stands. We've been at this since 2018, we've serviced more than 25,000 grills, and our team has 50+ years of combined grill experience.
We work throughout Brentwood, including:
- Brentwood Park
- Brentwood Glen
- Brentwood Circle
- Brentwood Village
- Brentwood Hills
- Mandeville Canyon
- Kenter Canyon
- Sullivan Canyon
If your street isn't named here, book anyway and we'll confirm we cover it.
Deep cleaning
Deep cleaning, start to finish
A deep cleaning takes the grill apart section by section and removes the baked-on grease and carbon. Here is what's included:
- Cooking grates scrubbed clean on both sides
- Burners cleaned, with the ports cleared so the flame is even
- Heat plates or flavorizer bars scraped, or flagged if they're burned through
- Briquette trays and briquettes cleaned
- Firebox scraped out, walls and bottom
- Drip tray and grease management emptied and cleaned so grease has a clear path out
- Igniter electrodes cleaned so they spark
- Hood and outside stainless cleaned and wiped down
- Our work area cleaned up before we leave
Buildup is more than a looks problem. Grease in the firebox and drip tray feeds flare-ups. Clogged burner ports give uneven heat, with one side searing and the other barely warm. Wet carbon holds moisture against metal and starts rust, and burners sitting in that mess rot out sooner.
A cleaning doesn't fix worn parts. If a burner or heat plate is past saving, we tell you and show you.

Start with the symptom
BBQ repair at your Brentwood home
Most grill trouble comes down to a handful of parts: burners, valves, igniters, grates, briquettes, heat plates, knobs and regulators. We repair all of them at the house, and the truck carries parts for most brands. These are the problems we see most.
Burners rusted through
Moisture and grease eat burner tubes from the outside in, leaving holes and flaking metal. Flames then come out in the wrong places. We replace the burners and clean the ports and venturi tubes while we're in there.
Igniter clicks but won't light
A corroded electrode tip, a loose wire or a dead battery usually keeps the spark from reaching the gas. We clean or replace the electrode, check the wiring and module, and test until it lights reliably.
Hood hinges and handles failing
Corrosion eats hinges, pins and handle hardware until the lid sticks, sags or a handle wobbles loose. We replace the worn hardware and re-hang the hood so it opens and closes properly.
Knobs that spin or valves that stick
Stripped knob stems, seized valve stems and gummed-up valves keep gas from turning on and off cleanly. We free or replace the knob or valve, then check for leaks.
Won't stay lit
A regulator on its way out, a clogged burner or a weak gas connection is the usual cause. We test the pressure, clean the burner and replace the regulator if that's the problem.
One burner is weaker than the rest
Debris or a spider web in the venturi tube, or clogged ports, starves a burner of gas and air. We clear or replace the tube and burner and balance the flame.
Smells like gas
Shut the gas off at the tank or valve and don't light the grill until it's been checked. Leaks tend to be at a hose, fitting, valve or regulator, and we find the source and repair it.
Heat shields and briquette trays burned through
These parts take the drippings and the heat, and eventually they give out. Grease then reaches the burners and flares up. We fit replacements sized to your grill.
Repair it right
We diagnose before we buy parts
The same symptom can have different causes. A grill that won't light might need an igniter, a regulator or just a clean burner. A weak flame could be a blocked tube or a bad regulator. Swapping parts on a guess fixes nothing and wastes your money.
So we check first: gas supply, regulator, valves, burners and ignition. Then we name the cause and fix it. The truck carries parts for most brands, and anything else we order from store.progrill.com, which stocks parts for most built-in grills.
Before we arrive, take a photo of the model and serial number label. It's usually on the frame, inside a cabinet door or on the back of the grill. With it, we bring the right parts the first time.
Built-ins & outdoor kitchens
Built-in grills and outdoor kitchens
When one part fails on a built-in, repair is nearly always the better move. Pulling out a built-in means dealing with the counter, the island and the gas line. A new burner, valve or igniter is a far smaller job. Replacement only makes sense when the firebox or frame itself is gone.
We also design, fabricate and repair outdoor kitchens, so one company can handle the grill and the island around it. Beyond grills, we service smokers, griddles, pizza ovens, fireplaces and fire pits.

Inspections & maintenance
Inspections and regular maintenance
An inspection is a full check of gas, burners and ignition, finished with a written report. It tells you what works, what's wearing and what needs attention soon. It's a good idea before a busy grilling season, after a grill has sat unused, or when you buy a house with a built-in.
Most homes should clean every 6 to 12 months. If you grill several times a week, plan on the shorter end.
If you'd rather not keep track, the Protection Plan is a membership for scheduled cleanings. We have 2,500+ five-star reviews (Google, Yelp and Facebook) from people we've served.
Wear and tear
What wears grills out in Brentwood
Brentwood is a few miles from the Pacific, and that is hard on metal. Salt in the marine air rusts burners, grates and hardware faster, stains and pits stainless, and corrodes igniter tips.
A cover or a roofed outdoor kitchen helps. So does a yearly cleaning with a look at the burners and electrodes, which catches corrosion while the parts can still be saved. Rust on grates and hinges is usually the first sign.
When it's time to replace
New grills, measured and installed
Sometimes repair stops making sense. The firebox has rusted out, the frame is failing, or the fixes add up to more than the grill is worth. Then we measure the cutout or the space, sell you a new grill, install it and haul the old one away.
Measuring first avoids the classic built-in mistake: a grill that's half an inch too big for the opening.

What to expect
What a visit looks like
- You book and tell us the grill and what's wrong
- The technician arrives and looks the grill over first
- We explain what we found and what it needs before we start
- We clean, repair or both, right at the grill
- We light every burner and check ignition and gas connections
- We clean our work area and go over what we did with you

