Start with the symptom
Grill cleaning and repair at your Glen Ridge home
We come to you. A technician pulls up with the tools and the most common parts on the truck and works on the grill right where it sits. You don't load a greasy firebox into the car, and you don't wait two weeks at a shop.
This matters most for built-ins. A grill set into an island can't be carted off, and most shops won't touch one. We work on it in place, whether it's a freestanding cart grill on the patio or a built-in under a covered lanai.
We've serviced over 25,000 grills since 2018, starting in Southern California and now also in Arizona and Florida. The team has 50+ years of combined grill experience, and we're insured.
Deep cleaning
Deep cleaning: what we do and why buildup matters
A deep clean is more than a scrape and a wipe. We take the grill apart far enough to reach the places grease and carbon hide, then put it back together and test it. Here is what's included:
- Cooking grates, scrubbed and inspected for rust and cracked welds
- Burners, cleaned and checked port by port
- Heat plates or flavorizer bars, scraped or replaced if they're too far gone
- Briquette trays and the briquettes in them
- Firebox, cleared of caked carbon and old grease
- Drip tray and grease management system, emptied and cleaned
- Igniter electrodes, cleaned so they spark where they should
- Hood interior and outside stainless, cleaned and polished
- Cleanup of our work area when we're done
Buildup is not just ugly. Grease on the heat plates feeds flare-ups. Clogged burner ports give you a flame that's strong on one side and weak on the other, so food cooks unevenly. Moisture trapped under a layer of grease speeds up rust, and a burner that sits in that for years rots out from the inside. Cleaning is cheaper than replacing burners.
We don't promise a cleaning will make an old grill like new. What you get is a grill that is clean, lights properly and cooks evenly for the condition it's in.

Start with the symptom
BBQ repair in Glen Ridge: the problems we see most
These are the repairs we're called for most often. If your problem isn't listed, describe it when you book and we'll tell you what we think is going on.
Stainless is pitted or stained
Salt and moisture get into the finish and leave brown spots and pinholes. We clean and treat what can be saved, and replace panels or hoods that are too far gone.
Knobs and valve stems are seized
Corrosion locks the stem inside the valve, and forcing the knob can snap it. We free the stem or replace the valve so the knob turns smoothly and shuts the gas off fully.
Burners are rusted through
Rust eats the burner tube from the outside and grease eats it from the inside. Holes cause weak, ragged flames and fire at the wrong spot. We replace the burner and clean the surrounding parts.
Grates are rusting or flaking
Bare cast iron and plated steel rust fast in damp air, and flaking means the coating is gone. We can often restore sound grates. If they're pitted or cracked, we fit new ones.
Igniter clicks but won't light
Usually a dirty or corroded electrode, a loose wire, or a dead battery or module. We test the spark, clean or replace the failed part, and check the gas path.
One burner is weaker than the rest
Clogged ports, a blocked venturi tube or a failing valve are the usual causes. We clear or replace whatever is restricting the flow.
Smells like gas
Shut the gas off at the tank or the line and don't light the grill until it's been checked. We test the hose, regulator, valves and connections to find the leak and fix it.
Briquette trays and heat shields burned through
Years of grease fires and heat wear the metal thin until it breaks. Without them the burners get direct drippings and the heat goes uneven. We replace them with parts that fit your model.
Repair it right
We diagnose first, then buy parts
The same symptom can come from different problems. A grill that won't light might need a new igniter, or it might have a stuck regulator or a blocked burner. Swapping parts by guess costs you money and leaves the problem in place.
So we check first, find the cause, and then repair it. The truck carries parts for most brands, and more are available at store.progrill.com if we need to order something for your model.
To speed things up, take a photo of the model and serial number label on your grill and send it when you book. It's usually on the frame, inside a door or under the control panel. With that we can bring the right parts the first time.
Built-ins & outdoor kitchens
Built-in grills and outdoor kitchens in Glen Ridge
When one part fails on a built-in, repairing it almost always makes more sense than replacing the grill. The cutout, gas line and surrounding stonework stay as they are, and you only pay for the part that failed. A burner, valve or igniter is a small job compared with tearing out an island.
We also handle outdoor kitchen design, fabrication and repair: islands, countertops, doors, drawers, side burners and the layout around the grill.
Grills are not all we work on. We service smokers, griddles, pizza ovens, fireplaces and fire pits as well.

Inspections & maintenance
Inspections and regular maintenance
A grill inspection is a full check of the gas supply, burners and ignition, plus the hoses, regulator, valves and connections. You get a written report of what we found, what's worn and what needs attention, so you can decide what to fix and when. It's useful before a big cookout, after a grill has sat unused, or when you're buying a home with an outdoor kitchen.
Most homes should have the grill deep cleaned every 6 to 12 months. If you grill several times a week, lean toward every 6.
If you'd rather not keep track, the Protection Plan membership puts regular cleanings on a schedule. We come out when it's due.
Wear and tear
What wears grills out in Glen Ridge
Glen Ridge is close enough to the coast that salt air and humidity are the main enemies. Salt settles on metal and holds moisture there, so burners, grates and stainless rust sooner than you'd expect. Igniter tips and electrodes corrode, which is why a grill that sparked fine last year suddenly just clicks.
Keeping up with cleaning and getting small rust problems looked at early slows this down. A cover helps, but trapped moisture under a cover can do its own damage, so let the grill cool and dry first.
When it's time to replace
When a new grill makes more sense
Sometimes repair doesn't add up: the firebox has rusted through, the frame is failing, or the cost of parts is close to the price of a new grill. We'll tell you plainly when that's the case.
If you decide to replace it, we measure the cutout or the space, sell you a grill that fits, install it and haul the old one away. For a built-in, getting the measurements right is the part that matters most.

What to expect
What a visit looks like
- You book online or by phone and tell us the grill type and the problem.
- A technician arrives in the window we gave you and looks over the grill.
- We explain what we find and what it will take before starting any repair.
- We clean, repair or both, and test the grill before we leave.
- We clean up our work area and go over what we did.
We have 2,500+ five-star reviews (Google, Yelp and Facebook). Booking takes a couple of minutes with the buttons on this page.

