Mobile service
We come to you in Glendale
Cleaning and repair happen at your house. Nobody loads a greasy grill into a truck or leaves it at a shop for a week. The technician arrives with tools, cleaning gear and a stocked truck, and works at the grill where it stands.
This matters most for built-ins. A grill set into a masonry or stainless island is not going anywhere, so the work comes to it.
We service homes throughout Glendale, including Adams Hill, Rossmoyne, Verdugo Woodlands, Chevy Chase Canyon, Sparr Heights, Tropico, Glenoaks Canyon, Whiting Woods, Verdugo Viejo and Citrus Grove. If your street is not named here, ask. We likely still reach you.
Pro Grill started in Southern California in 2018 and has serviced over 25,000 grills. The team brings 50+ years of combined grill experience, and we are insured. We have 2,500+ five-star reviews (Google, Yelp and Facebook).
Deep cleaning
Deep grill cleaning
A deep clean goes well past a quick scrape of the grates. We take the grill apart, clean each part and put it back together. A typical visit covers:
- Cooking grates, scrubbed and cleared of carbon
- Burners, with every port cleaned out
- Heat plates or flavorizer bars
- Briquette trays
- The firebox, scraped down to bare surfaces
- Drip tray and grease management system
- Igniter electrodes, cleaned and checked for a good spark
- The hood and outside stainless, wiped and polished
- Cleanup of our work area when we finish
Buildup is more than an eyesore. Old grease feeds flare-ups and can start a grease fire. Clogged burner ports give uneven heat, so one side scorches while the other stays pale. Trapped moisture and drippings speed up rust, and burners that sit in grime rot out sooner than they should. A clean grill lasts longer and cooks more evenly, though cleaning cannot fix parts that have already worn out.

Start with the symptom
BBQ repair in Glendale
Most repairs are finished in one visit. These are the problems we see most often in Glendale, and what usually causes each one.
Hot spots and uneven heat
Usually clogged burner ports, warped heat plates or a burner that has shifted out of position. We clean or replace what is blocked or bent and set the burners back where they belong.
Flare-ups and grease fires
Grease has built up on the heat plates, in the firebox or in the drip tray. We strip it out, clear the grease path and replace any plates too far gone to shed drippings.
Spider nests in the burner tubes
Spiders love the venturi tubes, and webs choke off the gas and air mix. The signs are yellow, lazy flames or fire burning at the knob end. We clear the tubes and check for damage.
Weak flame, stuck under 300°F
A regulator that has dropped into low-flow bypass mode is a common cause. We reset or replace it, then check the hose and valves so the grill gets full flow again.
Igniter clicks but won't light
The cause is a dead electrode, a loose or corroded wire, a dirty tip or a dead battery. We test the spark path and fix the weak link.
Smells like gas
Shut the gas off at the tank or the line and do not light the grill until it has been checked. The cause is often a worn hose, a loose fitting or a leaking valve. We test every connection and replace the faulty part.
Knob spins without turning on the gas
The knob has stripped or slipped off the valve stem, or the valve itself has failed. We replace the knob or the valve, whichever is actually broken.
Burned-through briquette trays and heat shields
Years of heat and grease eat through thin metal. Once the holes appear, flames reach the burners and heat turns patchy. We fit new trays and shields cut for your model.
Repair it right
We diagnose before you buy parts
The same symptom can come from different causes. A grill that will not stay lit might need a regulator, a cleaned burner or a new valve. Guessing means paying for parts you did not need, so we check first and tell you what we found.
If you can, snap a photo of the model and serial number label before we arrive. It is usually on the frame, inside a cabinet door or under the control panel. With it we can line up the right parts ahead of time.
The truck carries parts for most brands. For anything else, parts for most built-in grills are at store.progrill.com.
Built-ins & outdoor kitchens
Built-in grills and outdoor kitchens
When one part fails on a built-in, repair almost always makes more sense than replacing the whole grill. A new burner, valve or igniter costs far less than tearing out a cutout and a countertop. We repair in place and leave the island untouched.
We also design, fabricate and repair outdoor kitchens, from a single cabinet swap to a full island. And the same visit can cover your other fire equipment, since we service smokers, griddles, pizza ovens, fireplaces and fire pits.

Inspections & maintenance
Inspections and regular maintenance
A grill inspection is a full check of the gas supply, burners and ignition. You get a written report listing what is working, what is wearing and what needs attention, so you can decide what to fix and when.
Most homes should have the grill cleaned every 6 to 12 months. If you grill several times a week, lean toward the shorter end.
The Protection Plan is a membership for scheduled cleanings. We set the visits up, so you do not have to remember.
Wear and tear
What wears grills out in Glendale
Glendale is inland, so salt air is not the issue. Heat, dust and spiders are. Long hot stretches bake grease onto heat plates and firebox walls, and thin metal burns through faster.
Dust and debris settle in burner ports, and spiders nest in the venturi tubes. Both choke the flame. A yearly look inside the tubes and ports prevents many of the service calls we get.
When it's time to replace
New grills, measured, installed and hauled away
Sometimes repair does not make sense. The firebox may be rusted through or parts may cost more than the grill is worth. In that case we measure your cutout, sell you a new grill that fits, install it and haul the old one away.

What to expect
What a visit looks like
- You book online and pick a time that works.
- The technician arrives with tools, cleaning gear and common parts.
- We look the grill over and explain what we find before starting work.
- We clean, repair or both, and test the grill when we finish.
- We clean up our work area and go over what we did.

