Mobile service
We come to you in Encino
Our technicians drive to your house and work on the grill where it sits. Nothing gets hauled to a shop, no greasy firebox rides around in your trunk, and you don't go weeks without a grill. We cover Lake Encino, Encino Hills, Royal Oaks, Encino Oaks, Encino Terrace, Amestoy Estates, Encino Park and the streets around them.
Built-in grills are the easiest case for us, because they're set into masonry or a steel frame and can't be taken anywhere anyway. We work from the front of the island, pull the parts we need, and put everything back the way we found it.
Pro Grill has been doing this since 2018. We've serviced over 25,000 grills, the team has 50+ years of combined grill experience, and we're insured. We have 2,500+ five-star reviews (Google, Yelp and Facebook).
Deep cleaning
Deep grill cleaning, piece by piece
A deep cleaning takes the grill apart instead of just scrubbing the grates. On a typical visit we do this:
- Cooking grates: scraped, soaked and scrubbed, then checked for cracks and rust
- Burners: removed, cleaned, ports cleared, and checked for thin or rotted spots
- Heat plates or flavorizer bars: cleaned, or flagged if they've burned thin
- Briquette trays: emptied and cleaned
- Firebox: baked-on grease and carbon scraped from the bottom and corners
- Drip tray and grease management: emptied, cleaned, and the grease path cleared
- Igniter electrodes: cleaned and tested for a good spark
- Hood and outside stainless: degreased and wiped down
- Our work area: cleaned up before we leave
Buildup does more than look bad. Old grease feeds flare-ups and can catch fire inside the firebox. Clogged burner ports give you uneven heat and hot spots. Moisture trapped under carbon and grease starts rust, and burners that sit in that mess rot out sooner than they should. A cleaning costs far less than replacing a burner set.

Start with the symptom
BBQ repair at your Encino home
Most grill problems come down to a small part that has worn out or clogged. We fix them on site, usually in a single visit. These are the ones we see most.
Won't light
If the igniter clicks but the burner stays quiet, the cause is usually a dirty or cracked electrode, a dead battery or module, or a burner that isn't getting gas. We test the spark, clean or replace the electrode, and trace the gas path.
Weak flame or low heat
Dust, debris and cooked-on residue block burner ports and starve the flame. We clear the ports, clean the burner and check the gas pressure to find out what's holding it back.
Stuck in low-flow mode
A regulator can trip into bypass mode after a sudden gas surge, and the grill then won't get past a low, lazy flame. We reset it if it will reset, and replace the regulator if it won't.
Spiders in the venturi tubes
Spiders and nests block the tubes that feed gas to the burner, which gives you yellow flames or fire at the knobs. We clear the tubes, clean the burners and fit screens where the model allows.
Flare-ups and grease fires
Flames leaping through the grates mean grease is sitting where it shouldn't, often on worn heat plates or in a clogged drip path. We clean it out, replace what has failed, and fix the grease routing.
Burned-through heat shields
Briquette trays and heat shields take the worst of the heat and drippings, and eventually they get holes. We replace them with the right size for your model so the burners are protected again.
Knob spins but nothing happens
A knob that turns freely without opening the gas has a worn stem or a failed valve behind it. We swap the knob or the valve and test every position.
Smells like gas
Shut the gas off at the tank or the supply valve and don't light the grill until it's been checked. The usual causes are a loose fitting, a cracked hose or a worn valve, and we leak-test the connections and replace what failed.
Repair it right
We diagnose before we buy parts
The same symptom can come from different problems. A weak burner might be a clogged port, a bad regulator or a blocked venturi tube, and replacing the wrong part just costs you twice. So we check first, then fix what's actually wrong.
When you book, take a photo of the model and serial number label on your grill. It's usually on the frame, inside the cabinet door or on the back panel. It lets us bring the right parts the first time.
Our trucks carry parts for most brands, and we can order more from store.progrill.com. If a part is on backorder, we'll tell you before we start.
Built-ins & outdoor kitchens
Built-in grills and outdoor kitchens in Encino
A built-in grill with one bad part is almost always worth repairing. The grill head is the expensive piece, and the stonework and cutout around it were built to fit that exact size. Replacing a burner, valve or igniter costs much less than tearing out an island.
We also design, fabricate and repair outdoor kitchens: islands, counters, doors, drawers, side burners and the gas lines that run to them. Beyond grills, we work on smokers, griddles, pizza ovens, fireplaces and fire pits.

Inspections & maintenance
Inspections and regular maintenance
A grill inspection is a full check of the gas connections, hose, regulator, burners and ignition, finished with a written report. It's useful before a party season, after a grill has sat unused, or when you're buying a home with a built-in.
Most homes do well with a deep cleaning every 6 to 12 months. If you grill several times a week, plan for the shorter end of that range.
The Protection Plan membership puts cleanings on a schedule so you don't have to remember. We show up when it's due.
Wear and tear
What wears grills out here
In Encino, the main enemies are summer heat and dust. Dust and debris settle into burner ports and clog them, and spiders like the warm, sheltered venturi tubes. Both starve the burner of gas and show up as weak, yellow or uneven flames.
Heat also bakes grease onto heat plates and firebox walls, so it burns harder and longer. Cleaning before the heavy grilling months, and checking the venturi tubes while we're in there, takes care of most of it.
When it's time to replace
New grills, measured and installed
Sometimes repair stops making sense: the firebox has rusted through, parts are no longer made, or the repair bill would come close to a new grill. In that case we sell you a new one.
For a built-in, we measure the cutout first so the new grill fits the opening. We then install it, connect the gas, test it, and haul the old grill away.

What to expect
What a visit looks like
- You book a time and tell us what the grill is doing
- The technician arrives, looks over the grill and confirms the plan
- We clean, repair or inspect on site
- We test the grill, light every burner and check the flames
- We clean up our work area and go over what we found

